workin on the new module

Pins.md

@@ -1,4 +1,9 @@
-### U-BLOX LEA-M8T-0-10 HUAWEI GPS Module
+# Pins
+## Setup
+todo: splitter
+todo: buy links
+
+## U-BLOX LEA-M8T-0-10 HUAWEI GPS Module
 **Pins are 2mm pitch**
 **3.3 Volts**
 | Cable  | Module Pin | Module Pin Meaning       | Raspberry Pi 4 Pin         | Voltage                 | Notes                                                     |
@@ -7,17 +12,17 @@
 | Black  | 8 - GND        | Ground               | 25 - Ground                | 3.3 V?           | UNKNOWN 3 V AND 5 V TOLERANCES                            |
 | Yellow | 4 - RST        | Hardware Reset       | NC? - Not Connected/GPIO?  | 3.3 V            | NOT 5 V TOLERANT                                          |
 | White  | 6 - TP1        | Time Pulse 1/PPS     | 12 - GPIO 18               | 3.3 V            | NOT 5 V TOLERANT                                          |
-| Purple | 7 - TP2        | Time Pulse 2/PPS     | NC? - Not Connected/GPIO?  | 3.3 V            | NOT 5 V TOLERANT                                          |
+| Purple | 7 - TP2        | Time Pulse 2/PPS     | 16 - GPIO 23               | 3.3 V            | NOT 5 V TOLERANT                                          |
 | Green  | 5 - RXD        | UART Receive         | 8 - UART Transmit          | 3.3 V            | NOT 5 V TOLERANT                                          |
 | Grey   | 3 - TXD        | UART Transmi  t      | 10 - UART Receive          | 3.3  V           | NOT 5 V TOLERANT                                          |
 | Orange | 1 - VCC_ANT    | Antenna Power Supply | NC? Regulated Power Supply | 5.0 V Max 100 mA   | MUST USE REGULATED POWER SUPPLY AND UNKNOWN 3 V TOLERANCE |
 
-### Adafruit DS3231 Precision RTC Breakout
+## Adafruit DS3231 Precision RTC Breakout
 **Pins are 2.54mm pitch**
 **3.3 Volts**
 | Cable | Module Pin    | Module Pin Meaning | Raspberry Pi 4 Pin        | Voltage |
-|:------|:--------------|:-------------------|:-------------------|:--------|
-| Red   | 1 - VIN       | Voltage In         | 1 - 3v3            | 3.3 V   |
+|:------|:--------------|:-------------------|:--------------------------|:--------|
+| Red   | 1 - VIN       | Voltage In         | 1 - 3v3 Volts Out (Split) | 3.3 V   |
 | Black | 2 - GND       | Ground             | 9 - Ground                | 3.3 V   |
 | Brown | 3 - SCL       | I2C Clock          | 5 - GPIO 4 / SCL1         | 3.3 V   |
 | Green | 4 - SDA       | I2C Data           | 3 - GPIO 2 / SDA1         | 3.3 V   |

services.sh

@@ -7,5 +7,5 @@ if [ -z $1 ]; then
 fi
 
 echo "Running $1 on Services"
-sudo systemctl $1 gpsd chrony influxdb telegraf grafana-server syslog-ng 1>/dev/null
+sudo systemctl $1 gpsd chrony influxdb telegraf grafana-server syslog-ng
 echo "services complete" >> ./status.txt

todo.txt

@@ -1,8 +1,25 @@
 check max output mA on 5v to see if suitable to power antenna
-increase the baud rate
-    boot-firmware-config.txt /boot/firmware/config.txt
-    gpsd /etc/default/gpsd
+    needed or no?
 figure out multiple network time servers that support iburst NTS
     fiugre out what this means
         server nts.anastrophe.com iburst nts maxsamples 1
     https://gist.github.com/jauderho/2ad0d441760fc5ed69d8d4e2d6b35f8d
+fiugre out/test pps1 and pps0
+figure out configing the ffuckin thing in uthing
+    increase the baud rate
+        boot-firmware-config.txt /boot/firmware/config.txt
+        gpsd /etc/default/gpsd
+stop each service
+    bash services.sh stop
+start one by one to see any errors
+    try first
+        bash services start
+    otherwise
+        sudo systemctl start gpsd
+        sudo systemctl start chrony
+        sudo systemctl start influxdb
+        sudo systemctl start telegraf
+        sudo systemctl start grafana-server
+        sudo systemctl start syslog-ng
+find the proper datasheet not just the F9T one
+documentation